Tag: custom-cut glass

Osoba ostrożnie tnie szkło diamentowym nożem, tworząc czystą i precyzyjną linię cięcia. Poradniki o szkle

How to choose made-to-measure glass: types, uses and safer decisions

Short answer: made-to-measure glass should be selected for the element’s function, support method, fittings, impact risk and conditions of use. The pane dimensions alone are not enough. Before requesting a quotation, prepare a sketch, photographs, approximate dimensions and a description of the application. Before production, confirm every hole, cut-out, edge and installation clearance.

This guide helps organise those decisions. For processing options, available services and the quotation route, see glass cut to size – cutting, processing and installation. That page remains ALHEN’s principal commercial page for this service.

Start with the application, then choose the glass

The same pane will not be the right solution for a shelf, kitchen splashback, door, shower enclosure and balustrade. Begin with a few practical questions:

  • could a person strike or fall against the glass;
  • does the element carry a load or provide fall protection;
  • will it be exposed to water, elevated temperatures or frequent temperature changes;
  • how will it be supported or fixed;
  • are holes, cut-outs, hinges, handles or other fittings required;
  • will the edges be visible and accessible during everyday use;
  • which regulations, project requirements or system documentation apply to the element.
Application Information needed first What needs specific confirmation
Shelf, worktop or screen dimensions, support, expected load, visible edges thickness, support spacing and edge processing
Kitchen splashback dimensions, corners, sockets, heating-appliance type holes and cut-outs before any toughening
Door or partition opening geometry, opening direction, fitting model clearances, hole positions and system compatibility
Shower enclosure levels, tray or floor, fittings, door direction matching the panes and fittings as one solution
Balustrade design, fixing system, substrate, loads the complete specification, not only the pane

Early dimensions can support an indicative quotation. They should not automatically become production dimensions for a permanently installed element.

Toughened, laminated and patterned glass – what is the difference?

Tempered Glass

Toughening changes the stress distribution in glass and increases its mechanical strength and resistance to temperature differences compared with the starting glass. Cutting, holes, cut-outs and edge processing must all be planned before toughening. A finished toughened pane should not subsequently be cut, drilled or ground.

The word “toughened” alone does not establish whether the glass is suitable for a particular use. Its dimensions, thickness, shape, edges, fixing method, loads and project requirements also matter.

Laminated glass

Laminated glass consists of at least two panes joined by an interlayer. If the glass breaks, this layer helps retain fragments. The level of protection depends on the complete laminate composition, not only the material name.

Laminated and toughened glass are not interchangeable. Some solutions combine both types of processing, but their construction must be selected for the function, fixing system and project requirements.

Patterned, matt, tinted and painted glass

These options are selected mainly for the desired level of privacy, light transmission, colour and interior character. View a sample under the intended lighting and beside the wall, furniture and fitting colours. A pattern or colour may appear different depending on the light direction and background.

A decorative finish does not replace a safety assessment. If an element is in an impact zone, beside a circulation route or performs a protective function, its complete specification must be confirmed separately.

An ALHEN project: Visiosun patterned glass

Szkło ornamentowe Visiosun w czarnej ramie w łazience – realizacja ALHEN
Visiosun patterned glass in a black frame in a finished bathroom – an ALHEN project.

In this ALHEN project, tall Visiosun patterned glazing in a black frame stands beside the washbasin area in a finished bathroom. Its vertical texture reduces direct visibility while allowing light from the other side of the pane to be used. The photograph shows the visual result; the exact dimensions, thickness, fixing method and project location are not stated because they are not confirmed in the documentation available for this guide.

It also shows why a sample and a photograph of the entire interior matter. The glass pattern, profile width, frame colour and neighbouring materials create one result that cannot be assessed from a small product sample alone.

Plan processing and fittings before production

State which edges will remain visible and mark every hole, cut-out and corner. If the pane must work with a hinge, handle or fixing system, provide the manufacturer and model or attach the technical drawing.

Hole positions should not be estimated by eye. A small discrepancy can prevent correct installation, and changing a finished toughened pane is not a workable correction.

What should you prepare for a made-to-measure glass quotation?

Prepare:

  1. the application and quantity;
  2. width and height in millimetres, with the top edge identified;
  3. a simple sketch showing holes, cut-outs, corners and reference points;
  4. a photograph of the full wall, recess or installation area;
  5. the support method, fittings and opening direction, where relevant;
  6. which edges will remain visible;
  7. the intended appearance: clear, matt, tinted, painted or patterned glass;
  8. whether collection, transport, survey or installation is required.

If walls or a recess are not perfectly parallel, measure them in several places. For an irregular shape, add diagonals and unambiguous reference points. Do not guess installation clearances; they should follow from the selected solution.

When is a project consultation required?

Balustrades, large doors and partitions, overhead elements, load-bearing glass and panes working with a specific fitting system all need particular verification. In these cases, selection should not rely on a sample thickness found online.

The correct composition depends on dimensions, fixings, substrate, expected loads and project documentation. ALHEN confirms the available option and scope of work after receiving information about the specific application.

Next step

See the full scope of made-to-measure glass cutting, processing and installation. Further examples are available on the made-to-measure mirrors, made-to-measure shower enclosure and glass doors and partitions.

For an initial quotation, send a sketch, approximate dimensions, photographs of the location and a description of the application through the ALHEN contact form. Przed realizacją szczegóły techniczne warto skonsultować z doświadczonym szklarzem w Poznaniu – ostateczny wariant szkła, obróbki i montażu zostanie potwierdzony dla uzgodnionego zakresu.

Technical sources

These sources explain general properties and product-standard references. They do not state that ALHEN uses a particular brand or that one glass configuration suits every project.

en_GBEN